Views: 0 Author: Site Editor Publish Time: 2026-11-18 Origin: Site
A care worker receives a fall alert from a resident’s watch and calls to check.
“I’m fine,” the resident says. “I haven’t fallen.”
What caused the alert? Perhaps the resident made a sudden movement, or stumbled and recovered. The watch has flagged a possible incident, but someone still needs to find out what happened.
The opposite situation raises another question: if a fall occurs without an alert, did the watch miss it, or did the notification fail to arrive?
Understanding these differences helps care providers respond to alerts and give suppliers useful feedback.
Motion sensors measure movement. Software decides whether that movement resembles a fall.
Higher sensitivity may generate more false alerts; lower sensitivity may leave some falls undetected.
HW02 testing can begin with its current production sensitivity setting, followed by a review of daily use and alert feedback to assess whether adjustments are needed.
A watch measures movement at the wrist. It cannot directly observe the wearer’s whole body or what is happening around them.
An accelerometer, commonly used in fall-detection systems, measures acceleration along three axes. The software looks at these readings for patterns associated with a fall. Depending on the design, it may also consider changes in orientation or movement after an impact.
The sensor supplies the data; the software decides whether to flag an event.
This is difficult because the wrist moves independently of the body. A sharp arm movement may produce a strong signal without a fall, while an actual fall may produce less wrist movement than expected. Research using real-world fall recordings shows why results from controlled demonstrations do not always carry over to daily use.
Some movements share characteristics with a fall. If they meet the software’s detection rules, the watch may send an alert even though the wearer remains standing or seated.
Apple, for example, acknowledges that its watch can miss falls and can mistake high-impact activity for a fall. That is a useful example of the challenge, though it does not establish how HW02 performs.
When false alerts recur, ask what the wearer was doing at the time. Was there an abrupt arm movement? Did the watch strike something? Was it being worn according to the instructions?
Record the time and circumstances. A description such as “three alerts while doing the same household task” gives the technical team more to investigate than “the watch is too sensitive.”
Falls do not all look the same in sensor data.
A sudden impact, a slow slide from a chair and a fall partly interrupted by furniture can produce different signals. The wrist’s movement may also give an incomplete picture of what happened to the rest of the body.
If the recorded pattern does not meet the detection criteria, the watch may not recognize the fall.
An absent notification can have other causes too. The watch may not have been worn or powered on, or it may have recorded an event that did not reach the receiving app or platform. Check the available records before deciding that sensitivity is the problem.
A more sensitive setting makes the software more likely to flag movement as a possible fall. It may also trigger more alerts during ordinary activities.
Those alerts create work. A caregiver may need to call the wearer, establish what happened and record the outcome. Frequent false alerts can increase the time and cost of checking incidents.
A less sensitive setting may reduce these interruptions, but some falls may no longer trigger an alert. Research on sensor-based detection describes this trade-off between identifying falls and avoiding false alarms.
Fewer alerts do not necessarily mean better performance. Reported falls without alerts also need to be reviewed.
A remote alert involves three stages:
Stage | What needs to happen |
|---|---|
Detection | The watch recognizes movement that meets its fall-detection rules |
Delivery | The event or call reaches the intended contact, app or platform |
Response | Someone notices the alert, checks on the wearer and follows up |
Each stage can be checked separately. If the watch recorded an event but the platform did not receive it, investigate communication and delivery. If the notification arrived but nobody noticed it, review who monitors the account and what happens when that person is unavailable.
Adjusting sensitivity will not resolve either of those problems.
Testing can begin with the fall-detection sensitivity setting used in the current HW02 production version. During the pilot, observe how the watch performs in the intended users’ daily routines.
Keep a simple record of:
Alerts, including the time, activity and wearing conditions.
Whether a fall or stumble actually occurred.
Any reported fall without an alert.
Whether the notification arrived and someone responded.
KAER can review this feedback and adjust sensitivity in the software where appropriate. Agreed changes can be delivered through remote software updates, then evaluated again in daily use.
Keep the software version and setting with the test records so results before and after an adjustment can be compared. One false alert alone may provide too little information to justify a change; a recurring pattern is more useful.
Older users should not deliberately fall to demonstrate the feature. Any controlled fall testing requires a suitable procedure and personnel.
A wearer may need help without falling. They may also be able to press SOS after a fall that the watch did not detect.
Manual SOS gives them a deliberate way to request assistance, provided they can recognize the need, reach the button and activate it. Automatic detection may help when they cannot take that action, but it cannot guarantee that an incident will be recognized.
During setup, show the wearer how to use SOS and explain who will receive the request. For more on interpreting watch information, see Health Monitoring Watch for Seniors: What Can the Data Really Tell You?.
The KAER HW02 senior watch supports calling, manual SOS and automatic fall alerts.
KAER can adjust detection sensitivity through software and provide remote updates based on project feedback.
Planning a senior-watch or telecare project? Contact KAER to request samples. Share your intended users, receiving app or platform, and how your team plans to handle alerts.
No. It means the device identified a possible fall. Someone needs to check on the wearer to understand what happened and whether help is needed.
KAER can adjust sensitivity through software. Whether wearers or caregivers have access to a setting depends on the agreed device and application configuration.
Provide the event times, what the wearer was doing, how the watch was worn and the software version. Available device or platform records can also help distinguish a detection issue from a notification problem.